important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.

How to Install a Rear Derailleur

Removal and installation of a standard bolt-on rear derailleur.

In this tutorial we’ll learn how to replace a standard bolt-on rear derailleur.

Tools

For this job you’ll need a 5mm hex key for the derailleur’s mounting bolt, and a 2.5mm or 3mm hex key for the jockey wheels if you will not be removing the chain to clean or replace it. If you are removing the chain you may need a chain tool depending on your type of chain. You’ll also need wire cutters and a 9 or 10mm metric open end wrench, or a 5 or 6mm hex key to remove and install the rear shift cable. The last thing you’ll need is a phillips (+) screwdriver for adjusting the derailleur’s limit screws.

Rear Derailleur Removal

The first step is to shift your chain onto the smallest rear sprocket. Then pull off the shift cable’s end cap and loosen the cable pinch bolt. Remove the cable from the derailleur.

Now you’ll need to remove the chain from the derailleur. Some chains have a special connector pin that need replacing if removed, so if you don’t need to remove the chain for cleaning or replacement you can simply remove the lower jockey wheel and rotate the cage plate to release the chain. If you are removing the chain, disconnect a link and pull the chain through the jockey wheels.

Now you can unthread the derailleur’s mounting bolt all the way counter clockwise to remove the derailleur.

Rear Derailleur Installation

Before installing the new rear derailleur, apply some waterproof grease to the mounting bolt. Then thread it part way into the derailleur hanger, and rotate it clockwise to make sure the b-screw or tab is sitting behind the flat on the back of the hanger. Then fully tighten the mounting bolt.

If your chain is still on the bike, undo the bottom jockey wheel and thread the chain over the top pulley. Then re-install the lower jockey wheel. If you have removed the chain, re-route the chain through the jockey wheels and reconnect it. Search the site for tutorials on how to use a chain tool or a quick release chain link.

Rear Derailleur Set-up

Now preset the high-limit (H) screw so the upper jockey wheel is roughly in line with the smallest sprocket when viewed from behind.

Thread the shift cable back into the derailleur, pull it tight and tighten the anchor bolt so the cable flattens. Then find a bare stretch of cable and give it a good pull to make sure the cable is seated and has no slack. Then loosen the cable, pull it tight again and re-tighten it.

Now you’ll need to adjust the rear derailleur as shown in previous tutorials. If necessary, trim the cable so there is about 2 inches remaining. Then slide on a cable end cap and crimp it in place.

By Alex Ramon

A bicycle geek since early childhood, spent his twenties as a mechanic in bike shops. His passions include flatland BMX, unicycles, cycle touring, mountain biking and road riding.

Recommended Tools

Discuss this topic in the Bicycle Repairs and Mechanics Forum

Rear v-brake repair

Custom Bike part manufacturing

Removing and refitting rear wheel on belt drive bike?

Best way to thoroughly clean a chain?

Latest post 2 months ago

Hi everyone! I hope you're enjoying a great start to 2023. I'm curious to hear your go-to method for getting a chain truly clean. I don't mean, just looks shiny or is good enough for a quick clean after a ride. I want to know what you do when you want to get every last morsel of ground-up, link-destroying, roller-eating, tooth-gnashing crud out of your chain. The Best Chain-Cleaning Recipe Ever?...

What jockey wheel Red 10 Speed

Latest post 2 months ago

Can anyone advise what type of replacement jockey wheel I need for a 10 speed Red rear mech (it's got 11 teeth)? Bonus points if it's a link to a cheap (ish) one! Thanks...

Grip Shifters

Latest post 2 months ago

Currently renovating a child's bike. It has 24 inch wheels and is a suitable size for a 7-10 year old. Anyway it has grip shifters. it is a six speed with three chain rings on the front derailleur. On the rear derailleur the shifter does not appear to move the gear cable at all when shifting from 6 to 5 and 5 to 4. I am actually holding the cable with my finger and thumb against the cable cas...